Skip to content

How To Connect Pvc To Cast Iron Pipe Underground

PVC and cast iron pipes can be connected using a hub and spigot joint. The hub is a fitting that has a threaded end and is inserted into the cast iron pipe. The spigot is a PVC fitting that has a smooth end and fits into the hub. A sealant, such as plumber’s putty, is used to create a watertight seal between the two fittings.

How To Connect Pvc To Cast Iron Pipe Underground

There are a few ways to connect PVC to cast iron pipe underground. One is to use a coupling, which is a short piece of pipe with male threads on both ends. Another option is a bushing, which has one female end and one male end. The third option is a flange, which is a metal ring with bolt holes that can be used to attach PVC pipe to cast iron pipe.

– PVC piping – Cast iron pipe – Teflon tape – Pipe cutter – Hacksaw – Utility knife

  • Use a pvc primer to prepare the pvc pipe for
  • Cut the pvc pipe to the desired length
  • Dig a trench the width of the pipe and deep enough so that the pipe will be covered by 3 inches of soil

– When connecting PVC to cast iron pipe underground, it is important to use a primer and cement that is specifically designed for PVC and cast iron. – Make sure that the PVC and cast iron pipes are clean and dry before you begin. – Apply primer to the cast iron pipe, then apply cement to the PVC pipe. – Push the PVC pipe into the cast iron pipe until it is fully seated. – Give the joint a few good twists to make sure that it is


Frequently Asked Questions

Can You Connect Pvc To Cast Iron Pipe?

Yes, you can connect PVC to cast iron pipe, but it is not recommended. The two materials have different expansion rates, so the connection is likely to fail over time.

Can You Bury Fernco?

Yes, you can bury Fernco.

Can You Connect Pipe To Pvc?

Yes, it is possible to connect a pipe to PVC, but it is not always easy. The pipe and PVC will need to be cut to the same size, and then a hole will need to be drilled in the PVC. The pipe can then be inserted into the hole and secured with a clamp.

Can You Use Pvc And Metal Pipe Together?

Yes, you can use PVC and metal pipe together. PVC is a plastic pipe and metal is a metal pipe. They are both good for different reasons.

Can You Use No Hub Cast Iron Underground?

Cast iron piping can be used for underground applications, but it is not typically recommended to use no hub cast iron due to the potential for leaks. Cast iron can corrode over time and may not be as reliable as other materials.

How Do You Join Cast Iron And Pvc Piping?

Cast iron and PVC piping can be joined using a solvent weld. A solvent weld is a special type of adhesive that is used to join two pieces of piping. It is important to use the correct type of solvent weld adhesive, as not all adhesives will work with both types of piping.

Can You Mix Pvc And Metal Pipes?

Mixing PVC and metal pipes is not recommended, as the two substances can react with each other and corrode.

Can You Connect Ductile Iron Pipe To Pvc?

Yes, it is possible to connect ductile iron pipe to PVC, but it is not recommended. The two materials have different chemical properties and can corrode when they are in contact with each other.

Can You Mix Galvanized And Pvc?

Yes, you can mix galvanized and PVC. In fact, it’s a common practice to do so in order to create a strong, corrosion-resistant joint.

How Is Cast Piping Joined?

Cast piping is joined by welding along the seam. The weld is then ground down and cleaned to create a smooth, uniform surface.

Can You Mix Galvanized And Pvc Pipe?

Galvanized pipe is made of steel and is coated in zinc to prevent rusting. PVC pipe is made of plastic and does not corrode. It is possible to mix galvanized and PVC pipe, but it is not recommended. The zinc coating on the galvanized pipe can leach into the PVC pipe and cause it to corrode.


In Summary

There are a few ways to connect PVC pipe to cast iron pipe underground. One is to use a sleeve coupling, which is a type of fitting that slides over the outside of each pipe and is then glued in place. Another option is to use a transition fitting, which is a type of fitting that has one end that fits around the PVC pipe and one end that fits around the cast iron pipe.

Leave a Reply

Your email address will not be published. Required fields are marked *